http://www.techlore.com?src=category_rss TechLore - Televisions and Projectors Fri, 20 Nov 2009 23:28:08 GMT admin@techlore.com TechLore 60 http://www.techlore.com/brand/techlore/community.gif http://www.techlore.com?src=category_rss http://www.techlore.com/forum/thread/27673/Mitsubishi-WS-55613/?src=category_rss I was getting the green blinking led on my TV and after replacing the four 1000uf 35v caps the blinking has stopped. Now the TV and the led will not turn on at all! I do hear a chirp sound when I plug it in though. Any help is greatly appreciated. Thanks in advance! Televisions and Projectors Fri, 20 Nov 2009 23:28:07 GMT Joe777 http://www.techlore.com/forum/thread/27673/Mitsubishi-WS-55613/#discussion?src=category_rss http://www.techlore.com/forum/thread/27669/WD-52526/?src=category_rss WD 52526 My Mitsubishi WD 52526 - LIGHT IS BLINKING. I replaced the bulb, it was not working 100%. I replaced the house with a new bulb, it is not working. The gree light is blinking. Any suggestion? Thanks Walfredo de Freitas Televisions and Projectors Fri, 20 Nov 2009 15:50:24 GMT ispca http://www.techlore.com/forum/thread/27669/WD-52526/#discussion?src=category_rss http://www.techlore.com/forum/thread/27666/Mitsubishi-WT-42311-Red-Convergence-Problem/?src=category_rss I have a Mitsubishi rear projection TV (WT-42311). I can not adjust the red convergence horizontally. I replaced the convergence IC's (STK 392-110) with new Sanyo's, checked the pico fuses F9A02,03,04,05, and F9B01, F9D00(glass fuse), and F5A00 all are good. No change, still can not adjust red left or right. What is the next thing I can check? Any help would be greatly appreciated. Televisions and Projectors Fri, 20 Nov 2009 05:35:25 GMT Dale Bayle http://www.techlore.com/forum/thread/27666/Mitsubishi-WT-42311-Red-Convergence-Problem/#discussion?src=category_rss http://www.techlore.com/forum/thread/27665/bad-Tv-reception/?src=category_rss i have an older tv- and got one of those converter boxes--- sometimes i can get all 6 local channels fine--and sometimes i get the ----no signal-- warning------------ will buying a new tv help or will i need a new antennae? Televisions and Projectors Fri, 20 Nov 2009 04:08:57 GMT tvbmx http://www.techlore.com/forum/thread/27665/bad-Tv-reception/#discussion?src=category_rss http://www.techlore.com/forum/thread/27658/RCA-D52W19-Convergence/?src=category_rss I have an RCA model D52W19 rear projection tv. RGB colors are misaligned like 3D movie. Also has slight bowing effect top and bottom. I can go to the convergence menu and tried auto convergence but does nothing. Has anyone has fix to this problem? Please help!!! Cannot afford to buy a new tv. Televisions and Projectors Thu, 19 Nov 2009 18:23:16 GMT Patador http://www.techlore.com/forum/thread/27658/RCA-D52W19-Convergence/#discussion?src=category_rss http://www.techlore.com/forum/thread/27652/Mitsu-WS-55859-powers-up-for-2-secs-then-shuts-off/?src=category_rss About a year ago you guys helped me fix the green blinking light problem, THANK YOU! Now I have a new one, I was watching tv and it shut down, when I tried to turn it back on it would power up for about 2 sec. and then shut off, with no picture. last year i replaced the 7 capacitors in the DM module and a few months after the convergence IC went out and i replaced that. It's been about 8 months and this happened.can you help? Thank-you very much. Televisions and Projectors Thu, 19 Nov 2009 01:48:14 GMT John Doubek http://www.techlore.com/forum/thread/27652/Mitsu-WS-55859-powers-up-for-2-secs-then-shuts-off/#discussion?src=category_rss http://www.techlore.com/forum/thread/27649/kp-53hs30-replaced-ic392-560-wth-570-still-no-screen/?src=category_rss I replaced both ic chips and I am still not getting a picture. Makes a click and back to the 6 blinks. Checked the 2 picos on the G board and also the 7 picos on the D board. All have ohm reading. Not sure if this has anything to do with it but I went through resistors and only found resistor that gave no ohm reading. Which might be ok given the size of it. Its near where the outlet plug connects to the G board.Its quite a big resistor. I don't think this has anything to do with the 6 blinks though. but just thought I would throw that out there. I've checked my soldering and messed with it 3 times but still nothing. Any suggestions? Televisions and Projectors Wed, 18 Nov 2009 23:49:47 GMT wave http://www.techlore.com/forum/thread/27649/kp-53hs30-replaced-ic392-560-wth-570-still-no-screen/#discussion?src=category_rss http://www.techlore.com/forum/thread/27647/mitsubishi-ws-55311-power-on-then-right-back-off/?src=category_rss I ran the self test and got code 22 short protect circuit.What does that mean and how and what do i need to do? Televisions and Projectors Wed, 18 Nov 2009 17:17:05 GMT chuck margewich http://www.techlore.com/forum/thread/27647/mitsubishi-ws-55311-power-on-then-right-back-off/#discussion?src=category_rss